Ask Question
This is factory upgrade bushing featuring a standard 80 durometer proprietary polyurethane material pre-installed into a CNC machined aluminum bracket. With so much demand for these bushings we are making it that much easier to upgrade. Watch the video to see how they perform under pressure. These bushings replace the fluid-filled factory rubber bushings with Superpro Polyurethane Bushings that are built to last and properly engineering to increase performance. The high-end polyurethane design eliminates the parasitic spring rate caused by staked bushings and increase service life. These bushings also provide more positive front arm location during spirited driving while also will reducing inner tire wear* due to toe deflection under braking.
Set includes 2-Bushing sets to replace both bushings
INSTALLED INTO FIGS BILLET BRACKETS
Now Grey Anodized and new Hex design
includes grease
no shop press required since we include the brackets, just bolt-in.
Fits:
2001-2006 LS430 (must remove teardrop factory taper washer)
2006+ IS Vehicles
2006+ GS vehicles
2015+ RC-F
2016+ GS-F
2015+ RC350
Video of it in action
Install:
The bushing sits at the back of the front LCA which is held on by two bolts into the chassis and one nut that is threaded on to an extension of the arm.
You will need to remove both under-covers and the side bracket bolt that is attached to the #2 bushing bracket.
Remove the two bolts holding the bushing bracket (one with nut) and 2 side rail bracket
Remove the rear nut that holds the bracket to the LCA.
Remove rear bushing bracket, this may require deflection of the front arm bushing or unbolting the front location to free preload If too difficult you will need to remove the entire arm, sway bar and shock absorber. Contact FIGS is this is the case.
Install new bushings making sure the bevel on the bushing tube is oriented towards the front of the vehicle.
Reinstall rear nut to hold bushing in place but not to final torque.
Reinstall 2 bolts plus nut and 2 bolts of side bracket. Long bolt through side rail bracket torque to 204Nm/ 150ft-lbs, short bolt with nut 86Nm/63ft-lbs, and the side rail bolts 50Nm/37ft-lbs. Apply final torque to the nut at the center of of the bushing 113Nm/ 83ft-lbs.
Verify clean cycling of the suspension by loading and unloading. If any other OE or rubber bushings where loosened or replaced, load the suspension and then final torque them to prevent their premature wear.
You done!
*Alignment is still required to benefit from tire wear reduction.
Lexus | RC350 | 2015-2023 | |
Lexus | RC300 | 2016-2023 | |
Lexus | RC200t | 2016-2017 | |
Lexus | RC F | 2015-2023 | |
Lexus | LS430 | 2001-2006 | |
Lexus | IS500 | 2022-2024 | |
Lexus | IS350 | 2006-2024 | |
Lexus | IS300 | 2016-2024 | |
Lexus | IS250 | 2006-2015 | |
Lexus | IS200t | 2016-2017 | |
Lexus | IS F | 2008-2014 | |
Lexus | GS460 | 2008-2011 | |
Lexus | GS450h | 2013-2018 | |
Lexus | GS430 | 2006-2007 | |
Lexus | GS350 | 2013-2020 |
FRONT LOWER ARM REAR MOUNT #2 POLYURETHANE BUSHING 80 STANDARD INSTALLED IN BRACKET
- Brand: FIGS Engineering
- Product Code: L1035
- Availability: In Stock
-
$360.00
Related Products
FIGS STREET SPEC MEGA ARMS GEN 2 IS / IS-F V2
TECH DATA CNC machined 1018 steel end fittings. Formed steel construction. Flat sections dimp..
$964.69
FIGS MEGA ARMS GEN2 IS GEN3 GS STREET SPEC ESSENTIAL KIT FOR LOWERING
Making Lowering Simple The impact of lowering a second-gen IS or 3rd gen GS is dramatic. Camber,..
$1,443.12 $1,573.93
SPC MASTER BUSHING INSTALL TOOL KIT
Includes cups and threads to drive in just about any bushing imaginable. We found it a great asset ..
$720.00 $1,355.73
3GS 2IS/ISF REAR TRACTION LINK KNUCKLE MOUNT POLYURETHANE BUSHING
These bushings replace the staked rubber bushings on the knuckle-side mount of the rear traction lin..
$111.16
GEN 4 GS FRONT LOWER ARM REAR MOUNT #2 POLYURETHANE BUSHING
The outside diameter of these bushings is 85mm, if your bushing are the smaller 77mm you need to ord..
$151.18 $167.98
2-PIECE FRONT BRAKE ROTORS 2ND GEN IS / 3RD GEN GS
FIGS and RacingBrake have co-developed another 2-piece OEM replacement rotor for multiple Lexus vehi..
$1,025.00 $1,100.00
RB 4/2 POT CALIPER KIT (330x30/330x24) GEN2 IS GEN3 GS
FIGS and RacingBrake have co-developed another 2-piece OEM replacement rotor for multiple Lexus vehi..
$3,610.00 $4,000.00
RB 2-PIECE ROTOR KIT (380x34/342x28) GSF AND RCF
A 2-Piece Rotor Kit for the RC-F or GS-F.Includes front and rear rotors with XT910 pads...
$2,926.00 $3,080.00
4 POT CALIPER 2-PIECE FRONT BRAKE ROTORS 2ND GEN IS / 3RD GEN GS
FIGS and RacingBrake have co-developed another 2-piece OEM replacement rotor for multiple Lexus vehi..
$2,080.45 $2,211.00
FIGS TRACK SPEC MEGA ARMS GEN 2 IS / IS-F V2
TECH DATA CNC machined 1018 steel end fittings. Formed steel construction. Flat sections dimp..
$1,080.19
RB 2-PIECE REPLACEMENT FRONT ROTORS GSF AND RCF
Meant for use with the following brake kits.https://shopfigs.com/v5/LX-IRK-02https://shopfigs.com/v5..
$764.42
RB 6/4 POT CALIPER KIT (380x32/360x26) IS500
The IS500 6-piston front and 4-piston rear caliper kit is a high-performance braking system designed..
$6,000.00 $6,479.00
FIGS MEGA ARMS GEN2 IS/IS-F GEN3 GS PERFORMANCE SPEC ESSENTIAL KIT FOR LOWERING
Making Lowering Simple The impact of lowering a second-gen IS or 3rd gen GS is dramatic. Camber,..
$1,543.12 $1,773.93
Tags: 48075-30030, 2006+, is350, is250, isf, rcf, rc350, fsport, ls430, gs450h, gs350, rcf, gsf, RC-F, GS-F, is 350, is 250, is f, rc f, rc 350, f sport, ls 430, gs 450h, gs 350, gs f, IS-F, Front, Lower, Arm, Rear, Mount, #2, Polyurethane, Bushing, 80, Standard, INSTALLED, IN, BRACKET, 3491, 3491-80, SPF3491-80K