Ask Question

To complement our other link and arm offerings, we now round out the set with rear adjustable upper control arms (RUCA) for the 2001-2005 LS430 and UCF30/31 chassis.  We have built these arms like a tank with interlocking plate steel construction, lifetime poly bushing or spherical inner bearing options and high-misalignment outer spherical ball joint to handle the extreme camber angles of VIP suspension setups.  We also took note of what over-priced Japanese brands lacked and added a tie off bracket for the rear brake wear indicator cable and offer semi-custom length options so that you can dial in your wheel fitment. 

 

Features

  • Steel plate boxed construction for max strength.
  • 100% Precision TIG welded with interlocking overlapping structure. End fitting is double pass welded to ensure strength and tie in.
  • Preset or custom ball joint positions for precise wheel fitments. This includes Camber Correcting, VIP and VIP extreme.
  • SuperPro Lifetime Poly bushings for inner mounts or custom Precision FK PTFE Spherical Bearings(20% restocking fee if canceled after 24hrs on the bearing version).
  • Outer ball joint replaced with Precision High-Misalignment PTFE Rod end and monolithic Chromoly taper stud.
  • Outer ball joint set with Belleville washer on the jam nut for addition security.
  • Brake wear cable mount for passenger side rear to restraint cable replacing factory bracket designed for the factory arm.

 

Adjustment


Our rear arms are symmetric adjusted meaning you adjust both sides by the same amount via the outer rod end thread.  Though it may appear inconvenient, the upper arms should be adjusted as a fixed offset and infinite turnbuckle adjustments can create differences from side to side impacting handling, steering bias. Lower links offer the infinite adjustment for fine tuning and are a better place to manipulate camber and toe changes for a stable geometry.  Alignments are always iterative meaning as adjustments are made to one link, the other will need small adjustments as well.  By fixing the rear upper to a finite offset in graduations of 1/16" we are simplifying to overall alignment process.

 

Primary adjustment is done with the wheel off as a static offset.  Start with a deterministic number of turns on the upper rod end from fully seated.  This means thread it in completely, then spin it out the same number of turns per side.  The max strength of the rod end will de-rate after 10 turns outward or 0.625" of exposed thread beyond the jam nut.  We strongly suggest keeping the max thread engagement possible to maximize safety. A grade 8 jam nut can be used to extend this range by 2 threads.

 

Options


We build these with several options for customization and user input.  Camber goals are a starting point but given the specialized nature of wheel fitment and body work, we ask for a center point on the  arm length for custom setups and we will also provide a length offset number for our standard configurations.  This means for measurement purposes, we ask that you speculate on what the arm length should be to match vehicle geometry goals for best results. 

 

Camber correcting: max length will be 0.75" longer than stock, 0.75 adjustment range meaning it will only be longer than stock reducing negative camber.

VIP: VIP arms will be min length of 1.0" shorter than stock, this will put the arm slightly shorter than stock at its max length but add around -8 degrees of negative camber.

VIP Extreme: These arms are up to 2" shorter than stock and are made to handle extreme camber angles.  WARNING: At these positions, axle lengths should be verified and installer should ensure the axle will not get too short under suspension travel.  This will cause damage to the axle, diff or even worse the under carriage if a destructive condition exists.

 

SuperPro Poly Inner Mounts: The best for long life and low maintenance.  Lifetime poly features grooves to hold grease and a break-through material that is unlike any other Polyurethane on the market.  Guaranteed to not egg out, deform or migrate, this is the best Polyurethane we could find and we have looked all over the world.

 

Spherical Bearing Mounts:  The most precise, free-moving motion transfer connection, these bearings are a must for higher loads and stresses from aggressive wheel fitments. The bearings can product low speed squeaking related to the tight interface and PTFE fabric but PTFE dry lube worked into the interface should resolve the noise.

 

Safety and Maintenance

Like all of our products, these are arm provided for customers to use AT YOUR OWN RISK.  Proper setup, alignment and installation should be done with reasonable and prudent judgement and any concern should be raised immediately.  Arms should always be inspected within 100 miles of original install and inspection of jam nuts and mounting bolts should be verified to be fastened securely.  Rod ends should be centered on their mount to minimize bias and maximize misalignment. Rod ends should only be lubricated with PTFE dry lube and never grease.  Rubber boots are available however frequent internal lubrication is required again with a PTFE dry lube.

Lexus LS430 2001-2006

Write a review

Please login or register to review

LS430 REAR UPPER CONTROL ARM VIP AND CORRECTING

  • $1,488.38
  • $1,378.13


Available Options


Related Products

FIGS MEGA ARMS LS430 REAR VIP EDITION

FIGS MEGA ARMS LS430 REAR VIP EDITION

We have been testing these for a long time and due to time contraints it has taken us a while to put..

$606.38

FIGS MEGA ARM LS430 REAR LINK KIT VIP EXTREME EDITION

FIGS MEGA ARM LS430 REAR LINK KIT VIP EXTREME EDITION

This is a full rear arm set replacement including LCA, Toe, and Trac links to achieve up to -10 degr..

$1,047.38 $1,157.63

FIGS MEGA ARMS LS430 REAR CAMBER CORRECTING EDITION

FIGS MEGA ARMS LS430 REAR CAMBER CORRECTING EDITION

This version is intended to correct camber on lowered cars up to 2".  Toe and trac links are av..

$545.74

FIGS MEGA ARM LS430 REAR LINK KIT CAMBER CORRECTING EDITION

FIGS MEGA ARM LS430 REAR LINK KIT CAMBER CORRECTING EDITION

This allows for positive camber adjustments  after lowering your LS430 and camber correction. ..

$1,047.38 $1,157.63

LS430 REAR SWAY BAR LINK KIT

LS430 REAR SWAY BAR LINK KIT

DESIGNED TO FIX SWAY BAR PRELOAD ISSUES Application LS430 Includes 2 complete assemblies for b..

$119.99 $133.32

LS430 CORE REFRESH KIT

LS430 CORE REFRESH KIT

The time has come to refresh the front end of your LS430. Our core kit has the basics   Kit..

$157.19

LS430 CORE PLUS REFRESH KIT

LS430 CORE PLUS REFRESH KIT

The time has come to refresh the front end of your LS430. This kit is an upgrade over the core kit w..

$513.98

FIGS LS430 MEGA REFRESH KIT

FIGS LS430 MEGA REFRESH KIT

A total vehicle package for our customers that want the best value.  This kit our refresh kit w..

$1,515.94 $1,685.60

LS430 FRONT UCA WITH BUSHINGS

LS430 FRONT UCA WITH BUSHINGS

The LS430 Front Upper Control Arms (FUCA) from FIGS Engineering. Designed specifically for the Lexus..

$525.00

FIGS MEGA VIP KIT LEXUS LS430 2001-2006

FIGS MEGA VIP KIT LEXUS LS430 2001-2006

Elevate Your Ride to Unparalleled Luxury and StyleThis exclusive kit is meticulously crafted to tran..

$3,047.36 $3,257.89

ADJUSTABLE SWAY BAR LINK KIT

ADJUSTABLE SWAY BAR LINK KIT

DESIGNED TO FIX SWAY BAR PRELOAD ISSUES Includes 2 complete assemblies for both sides.   ..

$119.99 $133.32

LS430 OE STYLE FRONT LOWER CONTROL ARMS WITH BUSHINGS

LS430 OE STYLE FRONT LOWER CONTROL ARMS WITH BUSHINGS

Upgrade your LS430's suspension with the LS430 Front Lower Control Arms featuring preinstalled FIGS/..

$787.50

Tags: ls430, rear, Uca, camber, correction, inner, tire, wear, lowering, celsior, 2001, 2002, 2003, 2004, 2005, ucf30, ucf31, vip, ONIKYA, upper, arms, upper, control